5V Delay Relay Board Digital Delay Timer Control Switch Relay Module with LED Display
Rated 3.5/5 based on 11 customer reviews

5V Delay Relay Board Digital Delay Timer Control Switch Relay Module with LED Display

Available: Out of Stock

Overview:

  • Operating voltage: 6 - 30V DC 

  • 1 Channel delay trigerred relay module

  • Delay time: 0.1 second ~ 999 minutes 

  • Seven Segment Display

Description:

It is 6-30V 1-Channel Delay Power Relay Module with Onboard Adjustable Timing Cycle Switches with Digital LED display It is mostly used in Home Automation Delay Timer Control Switch Module Timer Controller. The Module operates at Operating voltage range of 6-30V, also it supports micro USB 5.0V power supply.  Output capability Can control the device within DC 30V 5A or AC 220V 5A. It can be applied to many fields as there is a wide range of application.

Features:

  • Wide voltage supply (6-30V) supports micro USB 5V power supply, which is very convenient to use

  • The interface is clear and simple, powerful, easy to understand, and almost meets all your needs

  • One-button emergency stop function (STOP key), with reverse polarity protection, reverse connection does not burn

  • Added sleep mode, enabled, no operation within 5 minutes, automatically turn off the monitor; any key wakes up

  • Can set different OP, CL, LOP parameters, these parameters are independent of each other, respectively, saved

  • All setting parameters are automatically saved and saved

Specifications:

  • Dimension: 6.2 * 3.8 * 1.7cm 

  • Operating voltage: DC 6V-30V (supports micro USB 5V power supply)

  • Trigger signal source: high-level trigger (3V-24V) signal ground and system to improve the system's anti-jamming capability (also short-circuit altogether)

  • Output capability: it can control the device within DC 30V 5A or within AC 220V 5A

  • Quiescent current: 20mA

  • Operating current: 50mA

  • Service life: more than 100,000 times

  • Working temperature: -40°C-85°C

  • With optocoupler isolation, enhanced anti-jamming capability, industrial grade circuit board, set parameters for memory after power failure.

Operation Mode:

  • P1: Trigger signal, the relay is on “OP” time, and then disconnect; Within the “OP” time, proceed as follows.

  • P1.1: the signal is triggered again, invalid.

  • P1.2: the signal is triggered again, re-clocking.

  • P1.3: Signal has triggered again, the relay is disconnected, stop the clock.

  • P-2: Trigger signal, after the “CL” time is off, the “OP” time is on. When the timing is completed, the replay will be disconnected.

  • P3.1: Trigger signal, after the “OP” time is on, the “CL” time is off, then cycle the above actions. If trigger signal within the loop, the relay will be disconnected and stop the clock. The number of cycles ( “LOP “) can be set.

  • P3.2: No need to trigger the signal after powering up, the “OP” time is on, the “CL” time is off, then cycle the above actions; The number of cycles ( “LOP “) can be set.

  • P-4: Signal holding function. If the signal is triggered, timing is cleared, the relay remains on; when the signal disappears, the relay will be off when the “OP” time is over; if another signal is triggered during timing, timing will be cleared.

How to choose the timing range:

After setting the parameter value in the mode selection interface, press the STOP button to select the timing range.

  • XXX. The  decimal point is in one place, the time range is: 1 second ~ 999 seconds

  • XX.X  decimal point in ten, timing range: 0.1 seconds to 99.9 seconds

  • XXX  decimal point is fully illuminated, timing range: 1 minute ~ 999 minutes

How to set parameters:

1. First determine the relay operating mode
 
2. According to the working mode of the relay, in the main interface (when the module is powered on, it will flash the current working mode (default P1.1 mode), and then enter the main interface,) "Press and hold the SET button for 2 seconds to release ". Enter the mode selection interface, select the mode to be set (P1.1~P-4) by pressing the UP and DOWN keys;
 
3. After selecting the mode to be set (for example, P3.2), short-press the SET button to set the corresponding parameter, then the parameter to be set will blink (OP conduction time, CL disconnection time, LOP cycle times ("-- - "On behalf of infinite number of cycles)), through UP, DOWN adjust the parameter value, support long press (fast increase or decrease) and short press (increase or decrease 1 unit); after setting the parameter value, press STOP key shortly To select the decimal point position, select the time range (the corresponding time 0.1 seconds ~ 999 minutes); short press the SET button to set the next parameter of the current mode, the process is the same as above;
 
4. After setting the parameters of the selected mode, press and hold the SET button for 2 seconds to release it. The currently set mode will flash, and then return to the main interface. Setting the parameters is successful. Main interface: "000" (no decimal point) is displayed when the relay is not working. The relay is in working state with a decimal point;
 
5. Mode selection interface: long press the SET key to enter, after setting is complete, long press the SET key to exit, back to the main interface.
  
Note: The relay output is a passive contact and has no live output to control the on-off of a line.

Mode Select Interface:

Press and hold the SET key to enter; after setting, long press the SET button back on main interface

Activate Relay Mode:

  1.  NO: PO in power over time, the relay can be connected

  2. OFF: relay is not allowed to connect, when in the off state

In short main interface press the STOP key to achieve turn ON and OFF, the current state will flash; then back to the main interface
(this function is a function of a sudden stop, 1 key to turn off the relay)

Sleep Mode:

  1. C-P Sleep mode: within 5 minutes, no operation; nixie tube will close auto display, and a function program well

Note:

1. Press and hold the STOP button for 2 seconds can achieve change from C-P to O-d; Current state will flash and then return to the main interface

2. The relay contact is passive and electricity production; 1 channel has the control function on / off


Package Included:

  • 1 X Delay Triggered One Way Relay Module with Adjustable Timing Cycle

Overview:

  • Operating voltage: 6 - 30V DC 

  • 1 Channel delay trigerred relay module

  • Delay time: 0.1 second ~ 999 minutes 

  • Seven Segment Display

Description:

It is 6-30V 1-Channel Delay Power Relay Module with Onboard Adjustable Timing Cycle Switches with Digital LED display It is mostly used in Home Automation Delay Timer Control Switch Module Timer Controller. The Module operates at Operating voltage range of 6-30V, also it supports micro USB 5.0V power supply.  Output capability Can control the device within DC 30V 5A or AC 220V 5A. It can be applied to many fields as there is a wide range of application.

Features:

  • Wide voltage supply (6-30V) supports micro USB 5V power supply, which is very convenient to use

  • The interface is clear and simple, powerful, easy to understand, and almost meets all your needs

  • One-button emergency stop function (STOP key), with reverse polarity protection, reverse connection does not burn

  • Added sleep mode, enabled, no operation within 5 minutes, automatically turn off the monitor; any key wakes up

  • Can set different OP, CL, LOP parameters, these parameters are independent of each other, respectively, saved

  • All setting parameters are automatically saved and saved

Specifications:

  • Dimension: 6.2 * 3.8 * 1.7cm 

  • Operating voltage: DC 6V-30V (supports micro USB 5V power supply)

  • Trigger signal source: high-level trigger (3V-24V) signal ground and system to improve the system's anti-jamming capability (also short-circuit altogether)

  • Output capability: it can control the device within DC 30V 5A or within AC 220V 5A

  • Quiescent current: 20mA

  • Operating current: 50mA

  • Service life: more than 100,000 times

  • Working temperature: -40°C-85°C

  • With optocoupler isolation, enhanced anti-jamming capability, industrial grade circuit board, set parameters for memory after power failure.

Operation Mode:

  • P1: Trigger signal, the relay is on “OP” time, and then disconnect; Within the “OP” time, proceed as follows.

  • P1.1: the signal is triggered again, invalid.

  • P1.2: the signal is triggered again, re-clocking.

  • P1.3: Signal has triggered again, the relay is disconnected, stop the clock.

  • P-2: Trigger signal, after the “CL” time is off, the “OP” time is on. When the timing is completed, the replay will be disconnected.

  • P3.1: Trigger signal, after the “OP” time is on, the “CL” time is off, then cycle the above actions. If trigger signal within the loop, the relay will be disconnected and stop the clock. The number of cycles ( “LOP “) can be set.

  • P3.2: No need to trigger the signal after powering up, the “OP” time is on, the “CL” time is off, then cycle the above actions; The number of cycles ( “LOP “) can be set.

  • P-4: Signal holding function. If the signal is triggered, timing is cleared, the relay remains on; when the signal disappears, the relay will be off when the “OP” time is over; if another signal is triggered during timing, timing will be cleared.

How to choose the timing range:

After setting the parameter value in the mode selection interface, press the STOP button to select the timing range.

  • XXX. The  decimal point is in one place, the time range is: 1 second ~ 999 seconds

  • XX.X  decimal point in ten, timing range: 0.1 seconds to 99.9 seconds

  • XXX  decimal point is fully illuminated, timing range: 1 minute ~ 999 minutes

How to set parameters:

1. First determine the relay operating mode
 
2. According to the working mode of the relay, in the main interface (when the module is powered on, it will flash the current working mode (default P1.1 mode), and then enter the main interface,) "Press and hold the SET button for 2 seconds to release ". Enter the mode selection interface, select the mode to be set (P1.1~P-4) by pressing the UP and DOWN keys;
 
3. After selecting the mode to be set (for example, P3.2), short-press the SET button to set the corresponding parameter, then the parameter to be set will blink (OP conduction time, CL disconnection time, LOP cycle times ("-- - "On behalf of infinite number of cycles)), through UP, DOWN adjust the parameter value, support long press (fast increase or decrease) and short press (increase or decrease 1 unit); after setting the parameter value, press STOP key shortly To select the decimal point position, select the time range (the corresponding time 0.1 seconds ~ 999 minutes); short press the SET button to set the next parameter of the current mode, the process is the same as above;
 
4. After setting the parameters of the selected mode, press and hold the SET button for 2 seconds to release it. The currently set mode will flash, and then return to the main interface. Setting the parameters is successful. Main interface: "000" (no decimal point) is displayed when the relay is not working. The relay is in working state with a decimal point;
 
5. Mode selection interface: long press the SET key to enter, after setting is complete, long press the SET key to exit, back to the main interface.
  
Note: The relay output is a passive contact and has no live output to control the on-off of a line.

Mode Select Interface:

Press and hold the SET key to enter; after setting, long press the SET button back on main interface

Activate Relay Mode:

  1.  NO: PO in power over time, the relay can be connected

  2. OFF: relay is not allowed to connect, when in the off state

In short main interface press the STOP key to achieve turn ON and OFF, the current state will flash; then back to the main interface (this function is a function of a sudden stop, 1 key to turn off the relay)

Sleep Mode:

  1. C-P Sleep mode: within 5 minutes, no operation; nixie tube will close auto display, and a function program well

Note:

1. Press and hold the STOP button for 2 seconds can achieve change from C-P to O-d; Current state will flash and then return to the main interface

2. The relay contact is passive and electricity production; 1 channel has the control function on / off


Package Included:

  • 1 X Delay Triggered One Way Relay Module with Adjustable Timing Cycle

Shipping Policies

  • To ensure that your order reaches you in the fastest time and in good condition, we only ship through reputed courier agencies.
  • While we shall strive to ship all items in your order together, this may not always be possible due to product characteristics, or availability. However, we will inform you before doing it.
  • If you believe that the product is not in good condition, or if the packaging is tampered with or damaged, before accepting delivery of the goods, please refuse to take delivery of the package, and call our Customer Care +919659361116 or Contact us, mentioning your order reference number. We shall make our best efforts to ensure that a replacement delivery is made to you at the earliest.
  • You may track the shipping status of your order on our website, by clicking at Track your Order section.
  • Please note all items (including gifts) will be shipped with an invoice mentioning the price, as per Indian Tax Regulations.

Shipping Partners

  • We use FedEx, Aramex, Professional Services to ship our products to your destination as available during checkout and chosen by you.
  • We also can ship through EMS Speed post on special request to remote locations, if you think that our shipping partners do not have coverage or served you improperly. HOWEVER, WE CAN’T GUARANTEE TO COMPLY TO YOUR REQUEST. This is due to the reason each shipment content is being verified by the post office before accepting. If they feel that the item may be damaged, then they will not accept the shipment.

Shipping Time / Delivery Time

  • We make our best efforts to ship your order within the same day of the order. 99% of our orders are shipped within 24 Hours.
  • We ship on weekdays (Monday to Saturday), excluding public holidays. Orders placed on SUNDAY will be shipped only on MONDAY
  • Orders placed before 4.00 PM will be shipped on the same day except on Sundays and Public Holidays.
  • Shipments through FedEx / Aramex/ Professional Services, if created before 04:00 PM will be picked up by them on the same day. Otherwise, the shipment will be picked up only on the next day.
  • Though we can guarantee a delivery time of 2-5 days to anywhere in India, it is totally beyond our control. Each shipping companies have their own methods, intermediate transit locations, etc. and the delivery time is not predictable.
  • Please plan your order allowing sufficient time for the delivery instead of last-minute orders.

Guarantee/Warranty

All items are delivered with a standard warranty of minimum 15 days (unless otherwise specified in the product page) to protect the customers from any manufacturing defect. If you have any problems with your order, please notify us within this duration from the date of shipment of any defective product. You agree to pay for the return shipping on exchanges and returns and we will reimburse this cost upon verification of a defect with the product. We will replace or repair the damaged products at free of cost with shipping prepaid by us. In case, we do not have the product in stock to provide a replacement, we will issue a 100% refund. Furthermore, no warranty will apply if the Product has been subject to misuse, static discharge, neglect, accident, modification, or has been soldered or altered in any way.

To the product need to be exchanged, firstly, please send the photos of damaged products to us. We will estimate the damages then decide the best way to exchange or return the product. If the particular item is not in stock to replace, we will provide the full refund.

100% Refund/Replacement

We guarantee to provide accurate descriptions and high-quality product as mentioned in the website. In order to protect customers from shipping damage, item mismatch or parts missing, etc., we are providing 2 days time (From the date of order delivery) to report the complaint by going to my account section and then to your order, you will find an option for Request Refund. Our technical team will verify the submitted details visually and will issue RMA number to return the material. Once we received the product our experts will verify the issue reported and will send the replacement items to the customer shipping cost prepaid by us. In case, we do not have the product in stock to provide a replacement, we will issue a 100% refund. Furthermore, no warranty will apply if the Product has been subject to misuse, static discharge, neglect, accident, modification, or has been soldered or altered in any way. Due to the nature of the products we are selling and our strict quality policy, we are unable to offer order cancellation and return without a valid reason. ROBODIUM reserves the right to take the final decision on all refund request.

Changing or Canceling An Order

Need change something about your order or just want it canceled? You can ask us (by Email Only ) to change the items on your order, update an address or payment method, or just cancel it. Customer Service will get back to you by email within one business day regarding your request. Only orders that are still in status “Pending” or “Payment Verification” can be altered or canceled. If your order has already moved to a different status, you won’t be able to alter it or cancel it. In some cases, Order cancellation may attract 5% bank charges depending on the payment methods used by the customer. (It is because most of payment gateway providers collect their Commission even though order canceled and refunded.).Due to the nature of the products we are selling and our strict quality policy, we are unable to offer order cancellation and return without a valid reason. ROBODIUM reserves the right to take the final decision on all refund request.

Return Guidelines

Once we confirmed the faulty item cannot be repairable by the customer or by Remote Desktop (Team Viewer), we will issue the RMA Number, which you have to mention clearly on Shipping boxes. Do not write anything on the merchandise packaging (Product package). Defective unused merchandise will be replaced within 2 days of receipt. All returns must include a copy of the original packing list that came with your shipment.

Limits Of Responsibility

We accept no responsibility for improper installation of our products. Electrical polarity must be properly observed in hooking up electrical components.

Customer Reviews

Based on 1 review Write a review